This ensures that the AGC circuit keeps a higher level during recording and hence the playback volume is also increased. To improve that somewhat, a 47K ohm resistor is added from the AGC Input to the LED Output pin. The main complaint about this module is that the audio playback volume is on the weak side. If it doesn’t seem to be working, verify that the Audio Feedthru switch is in the OFF position. Pressing PLAYE should replay the audio that you just recorded. To make your own recording, press and hold the REC button and speak into the mic. Pressing PLAYE will play anything that may have been pre-recorded on the device during testing. To test the device, just apply power and ground to the header pins and hookup a speaker to the screw terminals. The sound quality is fair and good enough for most applications that would make use of this device. We embedded one in a Zombie operation game for a sound effect when the tweezers touched the side and it is perfect for Halloween effects and similar applications. The beauty of this module is that it is simple to use as it doesn’t have a lot of options to complicate things. A fairly large 10-100uF capacitor should be in series between the speaker output and the input of the amplifier to remove any DC offset. If driving the input of an amplifier, connect just one of the speaker outputs to the input of the amplifier. The power output can drive a small speaker or the output can be used to drive the input of an audio amplifier if a louder sound is desired. That will serve to speed up or slow down the playback which might be useful for creating sound effects. It is also possible to record at one rate and play back at another. R4 can be replaced, or the jumper can be removed and a different value can be jumpered from the header pin next to R4 to ground to change the recording characteristics per the table below. 100K is what sets the 10 second duration for the recording. It is put into the circuit with the jumper at location P2. The module ships with a 100K resistor in location R4 that is connected to the ROSC pin on the ISD1820P chip. As per the table below, a tradeoff can be made between using a shorter duration recording, but with a higher sample rate and bandwidth or the duration can be extended up to 20 seconds with a lower sample rate and bandwidth. A resistor placed between the ROSC pin and ground sets the oscillator frequency and therefore sample rate and thus the maximum duration of the audio. The ISD1820 chip has a Resistor Controlled Oscillator input (ROSC) input. LED Output – Normally HIGH, goes LOW when LED is lit In this mode of operation, any audio picked up by the mic will be sent directly out to the speaker REPEAT Switch – if moved to the right will play the recorded message continuously.įT Switch – if moved to the right will enable a Feed Thru mode of operation. Pressing the pushbutton will play the recorded message until the button is released or the EOM is reached. When pin goes HIGH, the message will play until the pin is set back to LOW or the EOM is reached. Pressing the pushbutton will play the entire recorded message. When EOM is reached the red LED will flash. The pin can be set LOW while message plays and it will not terminate the message. The recording will play until the EOM is reached. PLAY Edge – Pin is edge activated when it transitions to HIGH. Release the button to stop the recording. Pressing and holding down the pushbutton will also record a message. Once the pin goes LOW or it runs out of memory, an End-Of-Message (EOM) marker is automatically recorded. RECORD – Pin is active HIGH to start recording and must remain high while the recording is in process. Functions such as Record, PlayE and PlayL can be activated by pushing a button or input a logic HIGH on the header pin with the same name. The main features of the module are shown below. The message can be rerecorded up to 100,000 times and is non-volatile.Ī small built-in audio amplifier can drive an 8 ohm speaker. This can be extended up to 20 seconds with a resistor change. With the built-in microphone, you can record one message that is up to 10 seconds long. Duration and sample rate can be modified up to 20 seconds with resistor change.Record and playback up to 10 seconds of audio.KEY FEATURES OF ISD1820 VOICE RECORD AND PLAYBACK MODULE: ISD1820 Voice Record and Playback Module.The ISD1820 Voice Record and Playback Module provides a simple way to record up to 10 seconds of audio and then play it back under MCU or manual control.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |